Original Retail $899.99, Now $699.99! You Save $200!
B-Stock Cliffwood Turntable & Audio Technica AT-VM95E Cartridge (Chocolate Truffle).
Limited Supply!
This product can only be shipped to U.S. addresses.
The VPI Cliffwood Turntable featuring an Aluminum Platter, 600rpm Motor, 9" Gimbaled tonearm & Audio Technica AT-VM95E!
For 40 years VPI has built turntables in America and kept it in the VPI family. For almost 30 of those years VPI has built their turntables in Cliffwood, New Jersey. With VPI reaching a more entry level market they are still able to make their products in Cliffwood, New Jersey. Most companies when making entry level products source their components outside their country of origin. This is why VPI is celebrating their heritage and own VPI workers by naming this turntable after the place they are built!
The tonearm is a 9" machined aluminum gimbal both easy and robust to use while providing top level sonic performance.
Features:
• Audio Technica AT-VM95E Cartridge
• 9" Gimbaled Tonearm
• Aluminum Platter
• 600rpm Motor
The Table:
• 1.25”" thick textured vinyl covered non-resonant MDF chassis.
• 16" x 11" footprint
• 19” x 14” x6” overall size
• Aluminum Platter
• Platter rotates on an oil bath bearing
• The bearing has a PEEK thrust disc and machined graphite impregnated brass bushings using a Thompson Engineering 60 Rockwell case hardened shaft.
The Tonearm:
• New 9” vertical Yoke type tonearm with lateral type bearing.
• Pivot to spindle: 223mm
• Effective length: 240.7mm
• Overhang: 17.7mm
• Offset angle: 22.85 degrees
• Average RMS distortion: .36%
• Damped machined aluminum armtube.
• Very pure copper wire, twisted with special insulating jacket.
• The armbase is upgradeable to a standard JMW 9 arm.
The Specifications:
Type: Belt drive (manual turntable)
Motor: 600 RPM AC Motor - 2 speed pulley
Turntable Platter: Aluminum
Diameter: 11.81” (30.0 cm)
Turntable Speeds: 33 1/3 rpm and 45 rpm
Cartridge: VPI/Grado Green
Dimensions: 18.5” (470 mm) W x 13.5” (343 mm) D x 4.3” (109 mm)H
Weight: 12.9 lbs. (5.9 kg)
Audio Technica AT-VM95E Cartridge:
Frequency Response 20-22,000 Hz
Channel Separation 20 (dB at 1 kHz)
Vertical Tracking Angle 23°
Vertical Tracking Force 1.8-2.2 g (2.0 g standard)
Stylus Construction Bonded round shank
Recommended Load Impedance 47,000 ohms
Coil Impedance 3.3 k ohms (1 kHz)
DC Resistance 485 ohms
Coil Inductance 550 mH (1 kHz)
Load Capacitance 100 to 200 pF
Output 4.0 mV (1 kHz, 5 cm/sec.)
Channel Balance 2.0 dB (1 kHz)
Stylus Shape 0.3 x 0.7 mil elliptical
Cantilever Aluminum pipe
Mount Half-inch
Weight 6.1 g (0.22 oz)
Dimensions 17.2 mm (0.68") H × 18.9 mm (0.74") W × 28.3 mm (1.20") D
Replacement Stylus AT-VMN95E
Available Upgrade:
Analog Drive System (ADS) for the utmost accuracy in motor speed and fine speed adjustments.
B-Stock Cliffwood Turntable & Audio Technica AT-VM95E Cartridge (Chocolate Truffle).
Limited Supply!
This product can only be shipped to U.S. addresses.
The VPI Cliffwood Turntable featuring an Aluminum Platter, 600rpm Motor, 9" Gimbaled tonearm & Audio Technica AT-VM95E! For 40 years VPI has built turntables in America and kept it in the VPI family. For almost 30 of those years VPI has built their turntables in Cliffwood, New Jersey. With VPI reaching a more entry level market they are still able to make their products in Cliffwood, New Jersey. Most companies when making entry level products source their components outside their country of origin. This is why VPI is celebrating their heritage and own VPI workers by naming this turntable after the place they are built!
The tonearm is a 9" machined aluminum gimbal both easy and robust to use while providing top level sonic performance.
Features:
• Audio Technica AT-VM95E Cartridge
• 9" Gimbaled Tonearm
• Aluminum Platter
• 600rpm Motor
The Table:
• 1.25”" thick textured vinyl covered non-resonant MDF chassis.
• 16" x 11" footprint
• 19” x 14” x6” overall size
• Aluminum Platter
• Platter rotates on an oil bath bearing
• The bearing has a PEEK thrust disc and machined graphite impregnated brass bushings using a Thompson Engineering 60 Rockwell case hardened shaft.
The Tonearm:
• New 9” vertical Yoke type tonearm with lateral type bearing.
• Pivot to spindle: 223mm
• Effective length: 240.7mm
• Overhang: 17.7mm
• Offset angle: 22.85 degrees
• Average RMS distortion: .36%
• Damped machined aluminum armtube.
• Very pure copper wire, twisted with special insulating jacket.
• The armbase is upgradeable to a standard JMW 9 arm.
The Specifications:
Type: Belt drive (manual turntable)
Motor: 600 RPM AC Motor - 2 speed pulley
Turntable Platter: Aluminum
Diameter: 11.81” (30.0 cm)
Turntable Speeds: 33 1/3 rpm and 45 rpm
Cartridge: VPI/Grado Green
Dimensions: 18.5” (470 mm) W x 13.5” (343 mm) D x 4.3” (109 mm)H
Weight: 12.9 lbs. (5.9 kg)
Audio Technica AT-VM95E Cartridge:
Frequency Response 20-22,000 Hz
Channel Separation 20 (dB at 1 kHz)
Vertical Tracking Angle 23°
Vertical Tracking Force 1.8-2.2 g (2.0 g standard)
Stylus Construction Bonded round shank
Recommended Load Impedance 47,000 ohms
Coil Impedance 3.3 k ohms (1 kHz)
DC Resistance 485 ohms
Coil Inductance 550 mH (1 kHz)
Load Capacitance 100 to 200 pF
Output 4.0 mV (1 kHz, 5 cm/sec.)
Channel Balance 2.0 dB (1 kHz)
Stylus Shape 0.3 x 0.7 mil elliptical
Cantilever Aluminum pipe
Mount Half-inch
Weight 6.1 g (0.22 oz)
Dimensions 17.2 mm (0.68") H × 18.9 mm (0.74") W × 28.3 mm (1.20") D
Replacement Stylus AT-VMN95E
Available Upgrade:
Analog Drive System (ADS) for the utmost accuracy in motor speed and fine speed adjustments.
