Normally $2294.99, Only $994.99! You Save $1300!
B-Stock Creek Destiny Power Amp!
Only 1 Available! 1 Year Warranty!
Creek Destiny Amp in perfect shape! Shipping/outer box looks used.
This item not eligible for any further discount offers!
The Creek Destiny Stereo Power Amplifier is designed to produce world beating audio performance, through its continued use of custom discrete analogue MOS-FET circuitry, which was first developed for Creeks amplification products in 1993. This circuitry has continued to be used with great success since that time and has evolved to meet the increasing demands for higher power, lower distortion and noise.
The Creek Destiny Stereo Power Amplifier uses separate power supplies and voltage referencing circuitry for each channel. Dedicated windings on mains transformer help it to achieve >100 Watts into 8 Ohm operation and nearly double that into 4 Ohms.
The Creek Destiny Stereo Power Amplifier uses the same protection circuitry as the Destiny Integrated Amplifier under fault conditions. Protection of the amplifier and ancillary products under fault conditions is facilitated by an array of sensors and measurement circuits feeding-back information to its microcontroller that monitors the amplifier constantly for over-temperature, over-current, DC offset, power supply status and over-drive situations. If any of these conditions is exceeded the microcontroller will take the appropriate corrective action. This can include, muting the input signal, separating the speaker outputs and in extreme cases, switching off the mains supply to the power amplifier circuitry. A log of fault conditions is stored in an internal memory device, which is also used to remember the last setting used prior to switching off the mains supply.
The Creek Destiny Stereo Power Amplifier is unusual in that it has two separate inputs. Firstly it has a non-inverting, input via high quality solid metal, gold plated RCA sockets that connect to the power amplifier directly. It also has active balanced inputs, via XLR sockets and uses relays to switch between the two inputs. The Destiny Power Amplifier can select either input from a button on the rear panel or using the Creek SRC2 System Remote Control handset.
Loudspeaker connection can be from bare wire or audio type instrument plugs, through high-grade touch-proof screw terminals that can be switched from the front panel or remote handset by gold contact high-current relays.
Like the rest of the Destiny range of products, the Power Amplifier can switch into low-current standby operation from the front panel or remote control handset. Waking up the amplifier can be performed simply via the Creek SRC2. For the ecologically aware consumer, the Destiny power amp draws less than 1Watt of mains power in standby mode.
The Destiny amplifiers metal case has been constructed from custom designed extrusions including solid 10mm thick front panel, 4mm thick extruded side and rear panels that combined with the 3mm thick top and bottom plate to make a very substantial heavyweight product. In addition the buttons and feet are machined by computer aided manufacturing techniques, to achieve a very high quality finish. To isolate mechanical vibration and improve sonic resolution custom designed 3mm thick moulded washers are stuck to the machined disc feet.
All in all, this is the best Power Amplifier Creek has made so far and will definitely compliment the integrated amplifier to achieve greater levels of current delivery for difficult loudspeakers loads. They are ideally suited to drive Epos Loudspeakers.
Power in to 8 Ohm both channel driven: Greater Than 100W
Power in to 4 Ohm one channel driven: Greater Than 250W
Max Current: Greater Than 25amps
THD: Less Than 0.02% 20Hz - 20Khz
Frequency Response: 1Hz - 30Khz - 1dB
Slew Rate: Greater Than 50 V per uS
Input Sensitivity: 589mv for 100W
Separation: Greater Than 60dB
Signal to Noise: Greater Than 78dB
Inputs: 1x unbalanced pair, 1x balanced pair
A/B speaker switch: Yes
Voltage: Switchable 115V / 230V
Power Consumption: 400W
Size W/H/D: 430 x 70 x 310mm